Pulse aquí para volver a la home de Danosa

WATERPROOFING, INSULATION & MORTARS

FOR BUILDING AND CIVIL WORKS


/link_RefPVC2.jsp
PVC base fitting Ø 75-125 mm pipes   
PVC Auxiliaries

 
 
Data Sheet
 
PVC base fitting for pipes which for tubes with diameter from 75 mm to 125 mm. Compatible with all DANOPOL membranes.

 Scope

Used as a waterproofing accessory for synthetic waterproofing PVC plasticized membranes, fitted with a wing that is welded to the waterproofing membrane.

 Presentation

PRESENTATIONVALUEUNIT
Shortest diameter125mm
Largest diameter75mm
Product Code 710258-

 Advantages and Benefits

Facilitates the membrane finishing on masts, pipes ventilation, emerging media, etc.
- High capacity for adapting to the support irregularities.
- Provides welding and finishing of high reliability.
- Compatible with all DANOPOL waterproofing membranes.

 Instruction for use

- The substrate surface must be solid, uniform, smooth, cleaned, dry and free from foreign bodies.
- Fully extend the PVC membrane, pierce it in proportion to the diameter of the drain, insert the nozzle into the pipe by hot air welding the crown to the membrane and insert the drain basket.

 Indications and Important Recommendations

-Incompatible materials in direct contact with PVC base fitting Ø 75-125 mm pipes waterproofing membrane: Bituminous products, XPS, TPO/FPO, EPS, EPDM, PU. DANOFELT PY300 or higher must be placed between both materiales to avoid chemical incompatibility or smooth any coarse surface.
- Make sure the chemical compatibility of PVC base fitting Ø 75-125 mm pipes with other materials.
- Weldability and weld quality depends on atmospheric conditions (temperature, humidity), welding conditions (temperature, velocity, pressure, cleanliness) and by the state of the membrane surface (cleanliness, humidity). Therefore must meet the hot air machine for the correct assembling
- Once the surface has been cooled, a strict welding control should be made using a blunt needle.

 Handling, Storage and Conservation

- PVC base fitting Ø 75-125 mm pipes is not toxic or flammable.
- PVC base fitting Ø 75-125 mm pipes should be stored in a dry place protected from rain, sun, heat and low temperatures. It should remain in its original packaging, horizontal and parallel (never crossed) on a flat and smooth support.
- PVC base fitting Ø 75-125 mm pipes will be used as soon at it arrives at the building construction.
- PVC base fitting Ø 75-125 mm pipes is easy to cut in order to adapt it to the work's geometry.
- No waterproofing works should be performed when weather conditions may be harmful, particularly when it is snowing or there is snow or ice on the deck, neither when the roof is covered by raindrops, surface moisture > 8%, or strong wind.
- No waterproofing works should be performed when the ambient temperature is less than -5 º C for hot air welding.
- In all cases, please keep Health and Safety standards at work, and good construction practice.
- Danosa recommends to consult this product TDS, which is available permanently at www.danosa.com or can be obtained by writing to our Technical Department.
- For any further clarification, please do not hesitate to contact our Technical Department.

 Warning

The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.
Orders are accepted in accordance with the terms of our current General Sales Conditions.
DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.

Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10


 Print