DANODREN H25 PLUS is a high density polyethylene (HDPE) brown nodular sheet bonded by thermofusion to a nonwoven calendered polypropylene geotextile. Its main use is for protection and vertical drainage.
Technical Data
TECHNICAL DATA | VALUE | UNIT | STANDARD | Longitudinal tensile strength | 19, -4 | kN/m | UNE EN ISO 10319 | Transversal tensile strength | 15, -4 | kN/m | UNE EN ISO 10319 | Longitudinal elongation | 75±15 | % | UNE EN ISO 10319 | Transversal elongation | 75±15 | % | UNE EN ISO 10319 | Static puncture resistance (CBR) | 2.5, -0.5 | kN | UNE EN ISO 12236 | Dynamic puncture resistance (cone) | 10, +5 | mm | UNE EN 13433 | Characteristic aperture measurement | 60 ± 5 | µm | UNE EN ISO 12956 | Water permeability perpendicular to the plane | 0,12 -0,02 | m/s | UNE EN ISO 11058 | Water flow capacity in the plane | 0.58552 | l/m.s | UNE-EN ISO 12958 | Durability | >25;suelo natural;4AÑOS | ANEXO B DE LA NORMA APLICABLE | | Dangerous substances | NPD | - | - |
Addtitional Technical Data
ADDITIONAL DATA | VALUE | UNIT | STANDARD | Compressive strength | 350 ±20% | kN/m² | UNE EN ISO 604 | Water permeability perpendicular to the vertical plane | 0,12 -0,02 | m/s | UNE EN ISO 11058 | Water permeability perpendicular to the horizontal plane | 0,002 -0,0002 | m2/s | UNE-EN ISO 12958 | Air volume between nodules | 5.9 | l/m² | - | Temperature range | -30 a 80 | ºC | - | Nodules number | 1907 | - | - |
Environmental Information
PARAMETERS | VALUE | UNIT | NORM | Pre-consumer recycled content | 20 | % | - | Post-consumer recycled content | 80 | % | - | Manufacturing Location | Fontanar, Guadalajara (España) | - | - | Volatile organic compounds (VOC) | PND | - | - | Solar reflectance index (SRI) | PND | - | - |
Standards and Certification
Main regulatory - EN 13252: Geotextiles and geotextile-related products. Characteristics required for use in drainage systems.
CE marking- In Accordance with the UNE-EN 13967 standard and complying with the Assessment and Verification of Constancy of Performances (EVCP) 2+ system, applied to all high density polyethylene products manufactured by DANOSA in Europe. This EVCP 2+ system requires, apart from the DoP (Declaration of Performance), an additional Certificate of Factory Production Control issued by a Notified Body (AENOR in this case.
Quality managementCompany registration BUREAU VERITAS according to EN ISO 9001 granted to DANOSA manufacturing plant in Fontanar (Guadalajara). Environmental managementCompany registration BUREAU VERITAS according to EN ISO 14001 granted to DANOSA manufacturing plant in Fontanar (Guadalajara).
Scope
- Drainage and protection of the waterproofing of buried walls in building and civil works, such as false tunnels and underpasses.
- Floors drainage and protection, when there is not hydrostatic pressure or the floor is over the phreatic level.
- Drainage for walkable inverted roofs with continuous pavements. The drainage is placed between the thermal insulation and the pavement.
Presentation
PRESENTATION | VALUE | UNIT | Length | 20 | m | Width | 2.10 | m | Roll surface | 42 | m2 | Rolls per pallet | 6 | rolls | Product Code | 314065 | - |
Advantages and Benefits
- Quick and easy installation.
- It provides a permanent drainage thanks to the chamber generated between the drainage sheet and the geotextile.
- The geotextile fused to the nodules, absorbs and filters the water of the ground, avoiding the filling of the drainage system and facilitating the evacuation of the water towards the drains.
- Due to the composition of the geotextile, polypropylene, DANODREN H PLUS can be left uncoated temporarily in the job site without deteriorating its mechanical and hydraulic properties.
- Resistant to breakage, impact and deformation.
- Resistant to chemical agent of the soil. Rot.
- Provides great durability of the building and the structures against humidity and external factors.
- Protection of the waterproofing against punching of soil.
Instruction for use
Buried walls - Surface and singular points must be uniform, clean, dry and free of foreign objects.
- The support of DANODREN H PLUS can be a waterproofing membrane.
- DANODREN H PLUS is placed with the geotextile against the ground.
- The geotextile layer has a width of 5 cm less than the drainage sheet to facilitate the overlap of roll with roll. To perform the overlap, the geotextile is detached 7 cm, exposing 12 cm of drainage sheet, where the overlap will be made with the following sheet.
- DANODREN H PLUS is fixed every 50 cm along the length and width of the overlap with DANODREN fixings. You can also use HILTI fixings, model X-SW.
- DANODREN H PLUS is fixed mechanically in their upper part with the DANODREN metallic profile. This protects the drainage layer of land dumping, filling and compacting of the ditch and the water entrance. This fixation must be done 10 cm over the waterproofing membrane.
- The corners should be made by folding the membrane.
- Lay the drain pipe.
- Rolls can be extended from top to bottom or vice versa and from left to right or vice versa, depending of the characteristics of work.
Floors- Where there is hydrostatic pressure or the floor is under the phreatic level, DANODREN H PLUS is extended with the geotextil against the ground. The overlaps are done as same as underground walls
Walkable inverted roofs with continuous pavement- In walkable inverted roofs with a continuous pavement, DANODREN H PLUS must be placed on the thermal insulation with the geotextile upwards. The overlaps are done as same as underground walls.
Indications and Important Recommendations
- DANODREN H PLUS drains, protects and filters.
- DANODREN H PLUS does not waterproof, therefore, it does not replace in any case the waterproofing membrane.
- DANODREN fixations must be used when placing DANODREN H PLUS.
- DANODREN metallic profile must be used when placing DANODREN H PLUS.
- Appropriate precautions must be taken not to puncture the waterproofing during the placement of DANODREN H PLUS.
- It must be verified that the product is at the site with its original packaging, duly labeled with CE marking and in perfect conditions.
- It is recommended to check the existence of Declaration of Performance.
- It is recommended to check the existence of the voluntary quality mark.
Handling, Storage and Conservation
- This product is not toxic.
- .The product should be stored in a dry place protected from rain, sun, heat and low temperatures and upright position.
- For further information, check the security data sheet.
Warning
The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product. Orders are accepted in accordance with the terms of our current General Sales Conditions. DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.
Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10
dñlgkdñfgksdñlgksñdgkl
 |
Declaration of Performance for the CE marking |
DoP DRE-002 for DANODREN H25 PLUS |
|
320 Kb
|
|
1.- Product and Company Identification
|
|
1.- Product and Company Identification
|
|
TRADEMARK: DANODREN H25 PLUS PRODUCT TYPE: high density polyethylene (HDPE) nodular sheet with geotextil MANUFACTURER/DISTRIBUTOR: DANOSA Calle La Granja, 3 28108 Alcobendas (Madrid, Spain) Phone number: +34 91 658 68 50
|
|
|
|
2.- Composition/Information on Ingredients
|
|
2.- Composition/Information on Ingredients
|
|
High-density polyethylene nodular sheet (HDPE) with polypropylene geotextile (Danodren Plus) or without geotextile (Danodren).
|
|
|
|
3.- Hazards Identification
|
|
3.- Hazards Identification
|
|
Identification of dangers: Under normal conditions, the product is not dangerous.
|
|
|
|
|
4.- First Aid Measures
|
|
Skin contact: In case of burns caused by hot substance, clean the area with plenty of cold water to remove heat. Consult a physician if burning sensation persists. ALL BURNS REQUIRE MEDICAL ATTENTION.
|
|
|
|
5.- Fire Fighting Measures
|
|
5.- Fire Fighting Measures
|
|
Appropriate extinguishing media: Dry chemical, Foam, CO2, Sand, Water spray. NEVER USE DIRECT WATER JET. Risks of exposure: Prolonged exposure to hot fumes causes respiratory problems. Fire fighting equipment for fire brigade: Respiratory protection.
|
|
|
|
6.- Accidental Release Measures
|
|
6.- Accidental Release Measures
|
|
6.1 INDIVIDUAL PRECAUTIONS None 6.2 ENVIRONMENT PROTECTION None 6.3 CLEANING SYSTEMS None
|
|
|
|
|
7.- Handling and Storage
|
|
Handling: No special measures required. Storage: Keep away from fire. Use in places with good ventilation, preferably with fire security system. Store under cover.
|
|
|
|
8.- Exposure Controls and Personal Protection
|
|
8.- Exposure Controls and Personal Protection
|
|
Personal protection: When manipulating hot product, wear protective clothing (helmet, gloves, boots, etc. resistant to high temperature). Avoid contact with skin. Under normal conditions it is not necessary to use breathing apparatus, it is enough with a good ventilation to minimise risk of overexposure to vapour, fumes or dust.
|
|
|
|
9.- Physical and Chemical Properties
|
|
9.- Physical and Chemical Properties
|
|
Physical state: Solid at room temperature. Colour: brown. Odour: Low. Characteristics of polyethylene membrane: weight: 500 - 900 g/m² compressive resistance: 100 - 400 KN/m² approx. tensile resistance: 400 - 700 N/60mm elongation at break, approx.: 30 % modulus of elasticity, according to ISO 178: 1500 N/mm² Geotextile characteristics: resistance to perforation: 1500 N tensile resistance: 8 kN/m pore size: 0.11 mm permeability: 100 l/ m².s
|
|
|
|
10.- Stability and Reactivity Data
|
|
10.- Stability and Reactivity Data
|
|
Conditions to avoid: It does not degrade with adequate use. Decomposition products: Thermal decomposition may produce fumes with carbon monoxide, that can ignite in presence of flames or infrared panels.
|
|
|
|
11.- Toxicological Information
|
|
11.- Toxicological Information
|
|
Primary irritative effect of the skin: It does not cause irritation. Eye irritation: The product is not irritating. Additional toxicological information: According to our experience and information, the product does not cause any adverse health effect if properly handled in compliance with standard systems.
|
|
|
|
12.- Ecological Information
|
|
12.- Ecological Information
|
|
It can be mechanically separated in a purification plant for waste water. With respect to the product´s consistency, there is no possibility of dispersion in the environment. For this reason, it does not cause any negative effect on the environment.
|
|
|
|
13.- Disposal Considerations
|
|
13.- Disposal Considerations
|
|
Recycle when possible. It can also be disposed of together with household refuse or incinerated, paying attention to technical regulations and having previously consulted competent authorities.
|
|
|
|
14.- Transport Information
|
|
14.- Transport Information
|
|
The product is NOT considered DANGEROUS for transport (ADR, RID, UN, IATA/ICAO).
|
|
|
|
15.- Regulatory Information
|
|
15.- Regulatory Information
|
|
The product is not considered dangerous. The product does not require special labelling.
|
|
|
|
|
16.- Other Information
|
|
This security data sheet is based on the European Community laws (91/155/CEE).
The information of the data sheet are true and exact. We do not guarantee recommendations or suggestions made here, because using conditions are out of our control. Consequently the user, under his responsability, has to decide if the information are appropriate or useful and if they don’t create any contractual juridical relation.
|
|
|
|