WATERPROOFING, INSULATION & MORTARS

Pasa = Positive or correct No pasa = Negative PND = No performance determined - = Not necessary

The membrane DANOPOL HS 1.5 DARK GREY ANTHRACITE, complies with EN 13956; EN 13967; EN 13361; EN 13491.EN 13362.
The membrane DANOPOL HS 1.5 DARK GREY ANTHRACITE, meets CE requirements.
The membrane DANOPOL HS 1.5 DARK GREY ANTHRACITE, has Environmental Product Declaration EPD No.S-P-00691.
The membrane DANOPOL HS 1.5 DARK GREY ANTHRACITE, has mechanical fixing systems BBA Agrément Certificate 14/5118.
The membrane DANOPOL HS 1.5 DARK GREY ANTHRACITE, has European Technical Approval (ETA) for mechanical fixing systems DANOPOL HS FM Nº 10/0054.

Waterproofing solutions, for new and existing buildings:
- Mechanically fixed flat roof waterproofing systems, commercial or industrial projects (EN 13956).

Civil work waterproofing:
- Basement waterproofing (EN 13967).
- Waterproofing fluid barrier in the construction of tunnels and associated underground structures (EN 13491).
- Reservoirs and dams waterproofing (EN 13361).
- Canals waterproofing (EN 13362).

ADVANTAGES:
- Excellent resistance to tearing.
- High dimensional stability.
- High tensile strength
- High puncture resistance
- Very good resistance to micro-organisms, putrefaction, mechanical impact, root penetration, natural aging, weathering, UV radiation and swollen.
- Excellent flexibility

BENEFITS:
- Improves performance in mechanically fastened sheets, assuming a high value of resistance to wind suction, optimizing the fixation density.
- Limits strains and tensions in the waterproofing membrane caused by high temperatures and temperature changes, very common in flat roofs.
- Absorbs structural movements.
- Presents good puncture protection to mechanical damage, derived from pedestrian transit, common in flat roofs.
- Very high durability to possible degradation related to chemical cases.
- High adaptability to different kind of supports.

Substrate preparation:
- The base support surface must be durable, uniform, smooth, be clean, dry and free from foreign bodies.
- As a separating layer or protective polyester geotextiles are used, type Danofelt PY 300 or higher.

Placement waterproofing layer:
-DANOPOL HS 1.5 DARK GREY ANTHRACITE Waterproofing membrane can be welded by hot air or by chemical THF bonding (Tetrahydrofuran)
- During the installation, the membrane's serigraphed face must remain in sight.

-Incompatible materials in direct contact with DANOPOL HS 1.5 DARK GREY ANTHRACITE waterproofing membrane: Bituminous products, XPS, TPO/FPO, EPS, EPDM, PU. DANOFELT PY300 or higher must be placed between both materiales to avoid chemical incompatibility or smooth any coarse surface.
- Make sure the chemical compatibility of DANOPOL HS 1.5 DARK GREY ANTHRACITE with other materials.
- Weldability and weld quality depends on atmospheric conditions (temperature, humidity), welding conditions (temperature, velocity, pressure, cleanliness) and by the state of the membrane surface (cleanliness, humidity). Therefore must meet the hot air machine for the correct assembling
- Once the surface has been cooled, a strict welding control should be made using a blunt needle.

- This product is part of a waterproofing system, please pay attention to all DANOSA documents and all rules and mandatory law in this regard.
- Special attention should be paid to the implementation of the singular points and special details.

- DANOPOL HS 1.5 DARK GREY ANTHRACITE is not toxic or flammable.
- DANOPOL HS 1.5 DARK GREY ANTHRACITE should be stored in a dry place protected from rain, sun, heat and low temperatures. It should remain in its original packaging, horizontal and parallel (never crossed) on a flat and smooth support.
- DANOPOL HS 1.5 DARK GREY ANTHRACITE will be used as soon at it arrives at the building construction.
- DANOPOL HS 1.5 DARK GREY ANTHRACITE is easy to cut in order to adapt it to the work's geometry.
- No waterproofing works should be performed when weather conditions may be harmful, particularly when it is snowing or there is snow or ice on the deck, neither when the roof is covered by raindrops, surface moisture > 8%, or strong wind.
- No waterproofing works should be performed when the ambient temperature is less than -5 º C for hot air welding.
- In all cases, please keep Health and Safety standards at work, and good construction practice.
- Danosa recommends to consult this product TDS, which is available permanently at www.danosa.com or can be obtained by writing to our Technical Department.
- For any further clarification, please do not hesitate to contact our Technical Department.

The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.
Orders are accepted in accordance with the terms of our current General Sales Conditions.
DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.

Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10